• CONTACT US 1-250-448-6806

  • ABOUT

Navigate to the Stitch in the Ditch Canada homepage

Check the icon Go to your Account!

  • 15+ Years In Business

  • Canadian Distributor for Westalee & Sew Steady Products

  • Give us a call: 1-250-448-6806

BELT New Home 110

BELT 21" Motor Belt New Home / Brother/ Janome/Kenmore 650166008

0 Reviews
C$17.99
C$13.99
You save C$4.00!
Product Code: 650166008
Quantity in Stock : 6 in stock!

Description

BELT Motor Belt 21"guaranteed to fit Janome (New Home)

BELT New Home 110 2003 2014 2015 2018 2022 Motor 21" 650166008
Brother, Kenmore, Elna, Janome, Pfaff Babylock

Babylock B15, B17, B21, BL16, BL18, BL18A Natalie, BL22, BL23A, BL1108, BL1170,
Brother LS1217 - LS1520, LS2125 - LS2720, LS2725, LS2820, LS2825, LS2920, PX100, PX150, PX200, PX300, RS15, RS25, RS35, VX1120, VX1125, VX1140, XL5010, XL5011, XL5012, XL5020, XL5021, XL5022, XL5030, XL5031, XL5032 , XL5050, XL5060, XL5070, XL5100, XL5130, XL5200, XL5232, XL5300, XL5340, XL5500, XL5600, XL5700 -
Elna 2002, 2004, 2006, 2100, 2110, 2130, 2300, 3003, 3005, 3230, -
Kenmore 385.1278180, 385.1278191, 385.1764180, 385.1792809, 385.1884180, 385.17724490, -
New Home / Janome 110, 2003, 2014, 2015, 2018, 2022, 2030, 2122, 2139N, 3015, 3018, 3123, 4618, 4623, 5018, 5024, 5124, Combi DX502, DX2015, DX2022, DX2030, HF1012, JF1004, JS1008LE, JW5622, MC5500, MC7000, MC7500, S3015, MS3015, My Excel 23L, SW2018,
Pfaff 1016,
Simplicity S180, SL1170, -
Viking Huskystar 207, 215 -
Alternative numbers 163XXL019, 650166019, 9865016600800, XA1196051
21 inch

Extended Information

To replace the belt:
Loosen the large screw that holds the motor in place (loosen – do not remove).
WHEN YOU LOOSEN THIS SCREW - PROTECT THE PAINT ON THE ARM OF THE MACHINE FROM THE SCREW DRIVER.
To locate this screw; look at the motor as if you are sewing – this screw is below and behind the hand wheel.
Loosening it will allow the motor to slide up and down.
Loosen the small screw on the silver stop motion knob on the large hand wheel.
Unscrew the stop motion knob and remove from the machine.
NOTE the stop motion washer - its 'ears' should be pointing out.
Remove the washer.
Pull the hand wheel off of the machine – the belt will come with it.
Remove belt from motor area.
Clean the backside of the stop motion knob, the stop motion washer, the inside of the large hand wheel, backside of the hand wheel, and the shaft the hand wheel goes on (inside and out).
Put a couple of drops of sewing machine oil on the shaft the hand wheel rides on (inside and out).
Install new belt on pulley on motor. (This is usually a two-handed job.)
Make certain it is on the pulley, riding in the groove, not on the outer rim.
Loop over hand wheel (the hand wheel is not on the machine, yet).
Replace hand wheel on machine.Replace washer ('ears' out) and then the knob. Tighten screw on knob (not too tight!).
Check to make certain the stop motion knob will release (partially unscrew).
If it will not, remove the knob and rotate the washer 180 degrees.
Replace the knob and check again.
Your new belt should be just tight enough to pull machine without slipping -- NOT ‘plucking’ tight! Actually, it needs to be pretty loose.
You can adjust the tightness of the belt by sliding the motor up or down.
It is VERY important NOT to run the machine with the belt too tight.
Having the belt too tight can cause the machine to run slowly and can damage or ruin the motor.
When the belt is adjusted correctly, retighten the screw that holds the motor on (remember to protect the paint on the arm of the machine from the screwdriver this time, too!).
You will be most successful adjusting the belt if you hold the motor in place while you are tightening the screw that holds the motor.

Reviews

Average Customer Review:
( 0 )

Join our newsletter today!